Antique American Wall Regulator by Seth Thomas, 80 Restored Original Clocks to choose from, Thomaston, Connecticut, full restored and completely original, circa 1910 dated case. Clock is 24" long, 16" wide, 5" deep, with an Arabic dial 11" minute track to minute track, 13" overall diameter. The dial is aged with some very fine scratches, see photos. Dial might be an original railroad dial. The Rail Roads only used Seth Thomas clocks with bold Arabic dials. The week duration non-chiming movement was completely rebuilt to new condition. An important fact is that the movement is original to the case. The movement retains its original Geneva stops, commonly referred to as overwind protectors. See below for details on restoration I performed. Also see photo which illustrates what a properly restored movement should look like. Over 80 Antique Clocks to choose from, ALL ON SALE. The quarter saw oak or tiger oak case was professionally refinished to a medium brown oak color. All clock that we refinish is done by hand and not placed in a caustic stripping vat. This way I can retain the original color of the wood and not damage the case. Both top and bottom glasses are original. The black background on the bottom glass was touched up. Clock has an excellent interior label, hands, pendulum and zinc and brass dial pan, hinges and bezel are original, movement is signed. All brass parts were polished to a mirror finish and sealed as they were 105 years ago. The clock was run and tested 30 days prior to being offered for sale. This is a very strong running and accurate timekeeping antique wall clock. A final note: Seth Thomas Regulator wall clocks like this one were the only clocks sanctioned for railroad use. You might think they all look the same but there is a difference. Seth Thomas clocks with a 12" drop and original Arabic numbers are legitimate railroad clocks. The 10" drops were not authorized for railroad use. The high quality movement in railroad clocks had the capability for extreme accuracy. Other Connecticut clock companies that produced similar looking clocks were not capable of the achieving the accuracy level of these Seth Thomas clocks. In 1910 the cost of these ST clocks was $7.80 as opposed to $2.25 for other companies. I have the best selection of these Clocks that I have had in years all are listed for sale. See photos. To purchase with MC or VISA please call Drury House Antiques 802-824-4395 EST or use PAYPAL
"The Following Is The Restoration Performed"
I am a purest and believe in preserving as much as humanly possible. The Value for Good Antiques is in Originality and Excellent Condition. Not Damaged, Broken, or comprised of non-original parts and overall dirty condition. I take an enormous amount of pride in the restoration work I preform. Generally the consumer has no idea of what in behind the face of the clock. Just because the clock ticks does not necessarily mean you have a good original clock. There is nothing more depressing when your clock stops working shortly after it was purchased and is taken to a clock professional for a physical evaluation only to discover the movement has extensive ware and requires $400 to $600 in repairs. This scenario is quite common and one that I have run into hundreds of times over the years. This definitely leaves a sour taste and you probably won't be buying another Antique Clock. To avoid situations like this, only buy your clocks from a reputable Antique Clock dealer with years of experience in restoration and only from a dealer who puts in writing the condition and the restoration work that was preformed. On-line purchases the dealer should provide detailed photos to include the clock movement. This is what we do and have done for over 35 years.
The clock movement was completely disassembled and cleaned in an Ultra Sonic cleaner. All pivots were resurfaced and polished on the Watch Makers lathe, 4 new bronze bearings were installed into worn pivot holes. I use the more expensive bronze bushings simply because they are harder and last longer than brass bushings. All bushing work in done by hand not with a drill press or bushing machine. This ensures the bushings are the correct size and are installed perpendicular. Once installed the interior of the bushing is polished with a smoothing broach and the oil sink is hand cut into the front of the new bearing, the back side is cut to remove troublesome burrs. All metal to metal wear was eliminated. The verge was hand stoned and polished with a Sapphire file then trued to the escape wheel. Then the clock was cleaned again in the Ultra Sonic cleaner to remove any metal particles, assembled and lubricated with the finest clock oil. The main spring was replaced with new one that was the correct length, width and strength. The clock now runs with a very strong pendulum amplitude as it should . I run and test my clocks for 30 days prior to being offered for sale. This is what I do and have done for the last 35 years. As a clockmaker, all work is performed to the highest Horological standard.
Basic Information You Should Know! For those of you who are not familiar with the term "Restoration", this simply means cleaning, waxing and repairing a clock or any other Good Antique back to original condition without alteration. The more an item is original the more it is worth. The less original the less it is worth. If the original mechanical clock movement is not original to the case then 90% of the established value is lost. This is fact not an opinion!
Polishing the Brass will not alter the Antique Value of a clock.
Not everyone can afford or even appreciate this level of restoration. However, that is no reason to perpetuate the misrepresenting and dishonesty by other clock sellers. There is a perfectly good reason why clock sellers will not show you the clock mechanism. #1 their clock is dirty, badly worn and probably not original to the case. #2 if it is shown it does not look like my clock movements. Saying that a clock is running good does not mean it will keep accurate time.
Many internet clock sellers claim that they guarantee the clock runs, however when the clock arrives and it does not. When the seller is contacted he simply passes the buck to the shipper that it was damaged in shipping and you the buyer should file a insurance claim. This gets him off the hook for selling a clock that was not in good order to begin with. If not packed properly the shipper will refuse the damage claim, Sound Familiar? My properly restored original Antique Clocks will provide years of uninterrupted service and pleasure. Hope this little tidbit of information aids you in making an intelligent decision on what to buy or NOT.
All of my clocks come with a correct fitting key, a set of instructions specific to this clock and the best packing in the business. I expect you to take the clock out of the box and have it up and running in a short time.